/ Home
/ SUBMISSION

/ The BJNANO
/ Diamond Open Access
/ Journal Statistics
/ Editorial Board
/ Community
/ Call for papers

/ Latest Articles
/ Most accessed
/ Thematic issues
/ Volumes
/ Authors

/ Alerts

/ TWITTER
/ LINKEDIN
/ Mastodon
/ RSS FEED

Empty search

Article Type

Publication Date Range

Search Tips

This search combines search strings from the content search (i.e. "Full Text", "Author", "Title", "Abstract", or "Keywords") with "Article Type" and "Publication Date Range" using the AND operator.

Search Examples

aromatic	the word “aromatic”
aromatic aldehyde	the word “aromatic” OR “aldehyde”
+aromatic +aldehyde	both words “aromatic” AND “aldehyde”
+aromatic -aldehyde	the word “aromatic” but NOT “aldehyde”
“aromatic aldehyde”	the exact phrase “aromatic aldehyde”
benz*	words which begin with “benz”, such as “benzene” or “benzyl”
benz*yl	words that begin with “benz” and end with “yl”, such as “benzyl” or “benzoyl”
benzyl~	words that are close to the word “benzyl”, such as “benzoyl” (i.e., fuzzy search)

BROWSE
Latest Articles
Most accessed
thematic issues
volumes
authors

BROWSE

Latest Articles Most Accessed Thematic Issues Volumes Authors

Author

2 article(s) from Gotsmann, Bernd

Combined scanning probe electronic and thermal characterization of an indium arsenide nanowire

Tino Wagner,
Fabian Menges,
Heike Riel,
Bernd Gotsmann and
Andreas Stemmer

Beilstein J. Nanotechnol. 2018, 9, 129–136, doi:10.3762/bjnano.9.15

PDF

Figure 1: Scanning thermal measurements of the InAs nanowire. (a) Setup for SThM measurements. (b) Topography...

Jump to Figure 1

Figure 2: Surface potential measurements of the InAs nanowire. (a) Setup for KFM measurements. (b) Topography...

Jump to Figure 2

Figure 3: Electrical characteristics extracted from KFM measurements. (a) Two-terminal I–V characteristics of...

Jump to Figure 3

Figure 4: Temperature profiles along the nanowire simulated from its electrical characteristics. The nanowire...

Jump to Figure 4

Album

Supp Info

Full Research Paper

Published 11 Jan 2018

Full text

Kelvin probe force microscopy for local characterisation of active nanoelectronic devices

Tino Wagner,
Hannes Beyer,
Patrick Reissner,
Philipp Mensch,
Heike Riel,
Bernd Gotsmann and
Andreas Stemmer

Beilstein J. Nanotechnol. 2015, 6, 2193–2206, doi:10.3762/bjnano.6.225

PDF

Figure 1: Contributions of apex, cone, and cantilever to the first (AM, left) and second (FM, right) order ca...

Jump to Figure 1

Figure 2: a) Sideband amplitude (blue) and phase (red) relative to the carrier oscillation measured during a ...

Jump to Figure 2

Figure 3: In-phase (red) and quadrature (blue) sideband amplitudes, normalised to the carrier oscillation amp...

Jump to Figure 3

Figure 4: Modulation indices of the sidebands at ω_m (a) and 2ω_m (b) against [Graphic 33] for different modulation amplitu...

Jump to Figure 4

Figure 5: Block diagram of a Kelvin controller based on a) a proportional–integral–differential (PID) control...

Jump to Figure 5

Figure 6: Closed-loop response of the Kelvin observer (black) and a proportional-integral controller (red) to...

Jump to Figure 6

Figure 7: Normalised closed-loop bandwidth (−3 dB) of the steady-state Kelvin observer as a function of the n...

Jump to Figure 7

Figure 8: Schematic of the modified KFM setup. For topography feedback, the cantilever is excited at a consta...

Jump to Figure 8

Figure 9: a) Topography, b) tip–sample capacitance gradient, C'', and c) local contact potential difference, U...

Jump to Figure 9

Figure 10: a), b) Kelvin and c), d) error signal of an InAs nanowire similar to the device shown in Figure 9, measured...

Jump to Figure 10

Figure 11: One-dimensional power spectral densities of the error signals in Figure 10c,d. Integral feedback works well a...

Jump to Figure 11

Album

Supp Info

Full Research Paper

Published 23 Nov 2015

Full text

Other Beilstein-Institut Open Science Activities

/ Help / Support & Contact / Alerts / Privacy Policy / Terms & Conditions / Impressum